To : PACTOR@WW
GB7CIP HF PACTOR PACKET INFO
GB7CIP HF PACTOR FREQUENCIES
Hello and thanks for your interest in reading this.
The following describes GB7CIP AX25 BBS System PACTOR frequencies.
Note: Relies on this Wireless AX25 BBS service
when the Internet links fail.
GB7CIP Lin_XFBB server forward scripts automatically controlling
SCS PTC-iiPro multimode controller
Kenwood TS480-Sat (No.1) (First operational November 2005)
Scanning, band and frequency selection
Switching between a ground mounted trapped vertical (80-10m)
and 3ele HF Beam (20,15,10m)
Rotator HAM VX/DCU1X and HF beam direction
Tones(4) 1400Hz/1600Hz USB for P1 P2 and P3 modes
CURRENTLY NOT ACTIVE ON HF PACKET GB7CIP's 2nd KENWOOD TS-480SAT
FAILS TO TRANSMIT FAULT (Failed December 2020) :(.....
Tones(1) 2100Hz/2300Hz USB 300bd or 600bd PACKET (manual mode change)
28128.4kHz Dial Frequency wire dipole
Mark frequency 28130.5kHz
GB7CIP Beacons every 6 minutes for netting purposes
g4apl Paul (gb7cip HF PACTOR)
Always looking for new HF AX25 PACTOR Forwarding partners.
Australia, New Zealand, Asia, South America, USA
He also likes having one to one HF PACTOR QSO's please arrange sked,
either via Centre Frequency 14110.6 USB (Dial 14109.00) using
Full Duplex (PD 1). Connect to GB7CIP BBS FBB_Convers
One connected and logged in, Enter the C (command) for the convers
server which Paul finds very usefull for support use as well.
Or via 14109.0 USB centre frequency used for one to one (Call CQ).
14107.5kHz USB Dial. using 1600/1400hz tones.
Recently during 2020/2021 COVID-19 Lockdown more Radio Amateurs are
coming on with their PACTOR SYSTEMS running P1, mode using non SCS
equipment (PK232, KAM Controllers that support PACTOR), as well
as others coming back on with their SCS PTC controllers.
Australia, Western Europe North Africa and now Central America.
If Paul notices you have logged on.
He will connect back. Using the above tones dial USB 14107.5kHz
PACTOR AX25 LinFBB Forwarding sessions commence hourly
at 28 minutes past the hour.
HF Pactor Frequencies being scanned for connections
Mark frequencies listed below are based on 1600hz 1400hz tones.
If you use different tones you will need to minus your
high tone from the USB Mark Frequency listed below to
get the USB dial frequency.
HF Beam Headings in unattended mode - Times in GMT/UTC (approx)
VK/ZL Long Path (South America) 22:28-00:27, Short Path 04:28-11:27
Central America 13:28-14:27
North America 01:28-04:27,16:28-22:27
Other Times Towards mainland Europe, Far East,
Africa and Short Path Oceania.
40M 24 hours 20M 00:00-23:59 UTC 15M 08:00-14:59 10M 08:00-14:59
MARK QRG USB DIAL QRG USB Mode
7048.00 7046.40 P1,P2
7050.00 7048.40 P1,P2
7051.50 7049.90 P1,P2,P3
14091.60 14090.00 P1,P2
14093.50 14091.90 P1,P2
14094.00 14092.40 P1,P2
14096.00 14094.40 P1,P2
14096.60 14095.00 P1,P2
14097.50 14095.90 P1,P2
14098.00 14096.40 P1,P2
14107.00 14105.40 P1,P2,P3
14107.50 14105.90 P1,P2,P3
14110.50 14108.90 P1,P2,P3
21098.00 21096.40 P1,P2
21098.60 21097.00 P1,P2
21098.80 21097.20 P1,P2
21096.60 21095.00 P1,P2
21112.00 21110.40 P1,P2,P3
28306.00 28304.40 P1,P2,P3 primary frequency
28130.00 28128.40 P1,P2
You can test the AX25 Mail path to GB7CIP.#32.GBR.EURO from your
home BBS. Using the PING route facility. By sending a message
in the following format to the GB7CIP PING Server..
Message: Body nothing require
with a /EX on a new line to end message
Current listed active AX25 BBS forward partners are
EU DB0ZAV F3KT IK0MIL IR0UGN IR2UFV OK0PBR UA6ADV UT1HZM YT7MPB
When propagation behaves itself. Which it is not currently!
I find this always interesting when HF paths are open.
Hope the above information was useful to you.
Background information can be found on the following web URL.
KEEP SAFE SPACE COLVID-19
73 de Paul g4apl SysOp GB7CIP